URO Parts
Login: /
# Part No Description New
1 930 106 023K-PRM Cylinder Air Baffle Kit
- Stainless Steel Cylinder Air Baffle Kit Includes: (6) 930 106 228 00 PRM (4) 930 106 023 01 PRM (2) 930 106 221 01 PRM (2) 930 106 222 01 PRM
2 930 106 220K-PRM Cylinder Air Baffle Kit
- Stainless Cylinder Air Baffle Kit Includes: (6) 930 106 228 00 PRM (4) 930 106 023 00 PRM (2) 930 106 221 00 PRM (2) 930 106 222 00 PRM
3 930 105 116 05 Valve Cover
- Lower Left/Right; "Turbo" style lower valve cover
4 901 107 291 00 Oil Tank Seal
- Seals oil filter opening to inner fender
5 911 375 043 00 Engine Mount
6 948 102 119 01 Acc. Belt Idler Pulley
- Left; w/ NTN bearing
7 951 375 042 04 Engine Mount
- Hydraulic; Not for tiptronic equipped cars
8 930 211 622 01 B Hot Air Hose
- Heat Exchanger to Heater Control Valve; 330 mm x 60 mm; Original dark brown paper/aluminum
9 955 104 484 01 Spark Plug Seal
10 911 110 365 01 Air Box Cover Strap
- For CIS injected 911 models only
11 996 107 237 52 Oil Separator Boot
12 996 107 313 51 Oil Filter O-Ring
13 914 504 155 10 Engine Compartment Seal
- These are pre-cut to 1 meter lengths.
14 948 105 934 00 Camshaft Adjuster Cap Seal
15 900 219 009 30-PRM Oil Drain Plug
- Hard Anodized Aluminum w/Magnet; 18 x 1.5mm
16 930 105 510 00 Chain Tensioner Sprocket Support
- Right
17 930 105 509 00 Chain Tensioner Sprocket Support
- Left
18 930 107 731 01 Engine Oil Dipstick
19 NCA2269CA Water Outlet O-Ring
20 911 504 115 02 Engine Compartment Seal
- Front; Short section
21 911 641 541 02 Oil Level Sender
22 948 102 120 01 Acc. Belt Idler Pulley
- Right
23 NCA2246BA Thermostat O-Ring
24 644 572 971 00 Hot Air Hose
- Gas Heater and Fresh Air Blower to Body; 60 x 1500mm; Original tan paper/aluminum
25 911 504 111 02 Engine Compartment Seal
- These are pre-cut with molded corners, seals engine compartment at the sides and along rear latch panel.
26 901 107 770 40 Oil Dipstick
27 930 107 731 00 Oil Dipstick
28 901 107 770 00 Oil Dipstick
29 964 375 043 81KIT Engine Mount Set
- HD RS Mount set; Replaces factory hydraulic mounts. Hardware not included Includes: (2) 964 375 043 81
30 901 108 291 00 Hot Air Hose
- Heat Exchanger to Air Filter Housing; 35 x 780mm; Original black paper/aluminum
31 996 107 023 55 Oil Separator
32 996 107 026 51 Oil Separator
33 996 107 023 04 Oil Separator
34 999 031 061 02K Cylinder Head Nut & Washer Kit
- This Kit Contains head nuts and "Small style" washers; used for 2.0-2.7L engines. Also original for Carrera 3.0 & 3.0 Turbo engines. Includes: (24) 901 104 382 02 (24) 999 031 061 02
35 999 031 091 01K Cylinder Head Nut & Washer Kit
- This Kit contains head nuts and "Large style washers"; used for 3.0 SC, 3.2 & 3.3 Turbo engines Includes: (24) 901 104 382 02 (24) 999 031 091 01
36 999 031 061 02 Cylinder Head Washer, Early Small Style
- Early Original Small Style; 24 required per engine; fits 2.0-2.7L engines.
37 999 031 091 01 Cylinder Head Washer, Late Large Style
- Late Large Style; 24 required per engine; 3.0-3.3L engines
38 901 104 382 02 Cylinder Head Nut
- Original HD style nut, no longer available from any other maker
39 901 101 161 02 Engine Case Washer w/ Chamfer
- 24 Required per engine. These go on the crankcase main through bolts.
40 928 110 363 01 Air Fillter Housing Strap
41 996 105 325 52 Spark Plug Tube
- Supplied w/ Viton o-rings
42 948 105 932 05 Valve Cover Gasket
43 948 105 931 03 Valve Cover Gasket
44 948 105 933 00 Spark Plug Holes Gasket
- For spark plug galley below valve cover
45 999 707 112 40 Oil Return Tube O-Ring
- Viton material, 8 required per engine
46 930 211 622 01 Hot Air Hose
- Heat Exchanger to Heater Control Valve; 330 mm x 60 mm; Original tan paper/aluminum
47 901 107 351 01K Oil Return Tube Kit - Finned Aluminum
- HD Finned Aluminum 1 piece tube design w/ Viton seals Includes: (4) 901 107 351 01 (8) 999 707 112 40
48 901 101 386 00-PRM Engine Sump Plate
- Stainless Steel construction; Original style with drain plug
49 901 211 194 01 Hot Air Hose
- Engine to Heat Exchanger; 60mm x 380 mm. Original tan paper/aluminum
50 911 211 522 00 Hot Air Hose
- Engine Compartment Blower to Rt. Heat Exchanger; 60mm x 1100 mm. Not for CA models; Original tan paper/aluminum
1